Tenda AC9和阿苏斯、TP-LINK的那些事儿 » 荒野无灯weblog

Keep It Simple, Stupid.

荒野无灯weblog

Tenda AC9和阿苏斯、TP-LINK的那些事儿

Tenda AC9这车很多人上了。硬改成16M闪存后可以完美使用阿苏斯(asus)RT-AC1200G+ 的固件。 本来故事到这里也就结束了。不料强大的恩山坛友又挖出一台TP-LINK ARCHER C1200 , 配置和 AC9 出奇地相似。

routerchart 资料:http://routerchart.com/tp-link/tp-link-archer-c1200-c1200-177#tsp tp-link us官网产品支持页:http://www.tp-link.com/us/download/Archer-C1200.html#Firmware

从routerchart的介绍可知,这款tp-link 2016年出的路由,配备有Broadcom BCM47189 @ 900 MHz CPU. 但是2.4G 和 5G 以及交换芯片未有提及。 从tp的支持页面可以下载到固件,v1的gpl源码,还可以看到一个emulator: http://www.tp-link.com/resources/simulator/1200(us)2.0_webpages-get/index.html 打开就可看到路由器的WEB UI.

从网上获取的资料看,V2版的ARCHER C1200硬件应该是和AC9一致的(并不确定。。。没有拆机图) 于是我试着拿V2的固件(Archer C1200(US)_V2_161130)刷入AC9看看。 从TTL串口显示的日志看, 是成功启动的:

Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .... 4674528 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: squash filesystem found at block 33
Creating 6 MTD partitions on "bcmsflash":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x000000ff0000 : "linux"
0x000000218000-0x000000ff0000 : "rootfs"
0x000000fb0000-0x000000fc0000 : "usb-config"
0x000000fc0000-0x000000fe0000 : "log"
0x000000ff0000-0x000001000000 : "nvram"
flash_chrdev :  flash_chrdev_init 
nflash: found no supported devices
PPP generic driver version 2.4.2
usbmon: debugfs is not available
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Registered led device: blue:lan1
Registered led device: blue:lan2
Registered led device: blue:lan3
Registered led device: blue:lan4
Registered led device: blue:usb_1
Registered led device: blue:wps
Registered led device: blue:wan
Registered led device: orange:wan
Registered led device: blue:status
Registered led device: blue:wlan_2g
Registered led device: blue:wlan_5g
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1954 buckets, 7816 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
brcmnand: found no supported devices
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
devtmpfs: mounted
Freeing init memory: 208K
ctf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ctf 22127 0 - Live 0x7f000000 (P)
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0xce4
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
bcm_robo_enable_switch: EEE is disabled
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.50 (r635252)
eth1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.50 (r635252)
et 71146 0 - Live 0x7f00e000 (P)
et 71146 0 - Live 0x7f00e000 (P)
emf 17251 0 - Live 0x7f02a000 (P)
igs 13399 0 - Live 0x7f037000 (P)
dpsta 4559 0 - Live 0x7f043000 (P)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 36, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hotplug detected product:  1d6b/2/206
hotplug detected product:  1d6b/2/206
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 36, io mem 0x1800d000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hotplug detected product:  1d6b/1/206
hotplug detected product:  1d6b/1/206
NTFS driver 2.1.29 [Flags: R/O MODULE].
fuse init (API version 7.15)
jffs2 not ready yet; using ramdisk

Please press Enter to activate this console. button cycle succeed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP MPPE Compression module registered
ip6tnl0: Disabled Privacy Extensions
L2TP core driver, V2.0
L2TP netlink interface
gre: GRE over IPv4 demultiplexor driver
GRE over IPv4 tunneling driver
bonding: Ethernet Channel Bonding Driver: v3.7.0 (June 2, 2010)
bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
NET: Registered protocol family 24
PPPoL2TP kernel driver, V2.0
PPTP driver version 0.8.3
nf_conntrack_rtsp v0.7 loading
nf_nat_rtsp v0.7 loading
reloadconfig() begin:
no userconfig
resetconfig() begin:
resetconfig() end:
error no config
reloadconfig() end:
reload_profile() begin:
error no profile
reload_profile() end:
Load database fail.
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
device eth0 entered promiscuous mode
UTC
device eth0 left promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: port 1(eth0) entering learning state
br-lan: port 1(eth0) entering forwarding state
Lan Domain: tplinklogin.net
Lan Domain: www.tplinklogin.net
br-lan: no IPv6 routers present
eth0.1: no IPv6 routers present
usbshare boot start
usbshare boot end
kcg 333 :GPL NetUSB up!
kc  227 : init_DebugD end
kc   90 : run_telnetDBGDServer start 
INFO182B: NetUSB 1.02.80, 00020624 : Feb 24 2016 11:18:15
INFO182D: 7437: Archer C1200 :Archer C1200 
INFO182E:  AUTH ISOC
INFO182F:  filterAudio
usbcore: registered new interface driver KC NetUSB General Driver
INFO01ED:  init proc : PAGE_SIZE 4096
INFO171F:  infomap 7f97f428 
INFO1722:  sleep to wait br-lan to wake up
INFO15D9: tcpConnector() started... : br-lan 
wl_module_init: passivemode set to 0x0
wl_module_init: txworkq set to 0x0
eth2: Broadcom BCM43c8 802.11 Wireless Controller 9.10.178.50 (r635252 WLTEST)
PCI: Enabling device 0001:01:00.0 (0140 -> 0142)
eth3: Broadcom BCM43227 802.11 Wireless Controller 9.10.178.50 (r635252 WLTEST)
INFO1589: Bind to br-lan
HTB: quantum of class 20002 is big. Consider r2q change.
HTB: quantum of class 22100 is big. Consider r2q change.
HTB: quantum of class 22101 is big. Consider r2q change.
HTB: quantum of class 22102 is small. Consider r2q change.
=====>>>>> wireless setting is finished

BusyBox v1.19.4 (2016-11-30 17:13:39 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

     MM           NM                    MMMMMMM          M       M
   $MMMMM        MMMMM                MMMMMMMMMMM      MMM     MMM
  MMMMMMMM     MM MMMMM.              MMMMM:MMMMMM:   MMMM   MMMMM
MMMM= MMMMMM  MMM   MMMM       MMMMM   MMMM  MMMMMM   MMMM  MMMMM'
MMMM=  MMMMM MMMM    MM       MMMMM    MMMM    MMMM   MMMMNMMMMM
MMMM=   MMMM  MMMMM          MMMMM     MMMM    MMMM   MMMMMMMM
MMMM=   MMMM   MMMMMM       MMMMM      MMMM    MMMM   MMMMMMMMM
MMMM=   MMMM     MMMMM,    NMMMMMMMM   MMMM    MMMM   MMMMMMMMMMM
MMMM=   MMMM      MMMMMM   MMMMMMMM    MMMM    MMMM   MMMM  MMMMMM
MMMM=   MMMM   MM    MMMM    MMMM      MMMM    MMMM   MMMM    MMMM
MMMM$ ,MMMMM  MMMMM  MMMM    MMM       MMMM   MMMMM   MMMM    MMMM
  MMMMMMM:      MMMMMMM     M         MMMMMMMMMMMM  MMMMMMM MMMMMMM
    MMMMMM       MMMMN     M           MMMMMMMMM      MMMM    MMMM
     MMMM          M                    MMMMMMM        M       M
       M
 ---------------------------------------------------------------
   For those about to rock... (Attitude Adjustment, r10131)
 ---------------------------------------------------------------
root@Akronite:/# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: sit0: <NOARP> mtu 1480 qdisc noop state DOWN 
    link/sit 0.0.0.0 brd 0.0.0.0
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
    link/ether 00:0a:eb:13:7b:00 brd ff:ff:ff:ff:ff:ff
4: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 00:00:00:00:0c:14 brd ff:ff:ff:ff:ff:ff
5: eth0.1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP 
    link/ether c8:3a:35:21:04:a0 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::ca3a:35ff:fe21:4a0/64 scope link 
       valid_lft forever preferred_lft forever
6: dpsta: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN 
    link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
7: ip6tnl0: <NOARP> mtu 1460 qdisc noop state DOWN 
    link/tunnel6 :: brd ::
8: gre0: <NOARP> mtu 1476 qdisc noop state DOWN 
    link/gre 0.0.0.0 brd 0.0.0.0
9: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN 
    link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
10: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc htb state UNKNOWN 
    link/ether 00:0a:eb:13:7b:00 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.1/24 brd 192.168.1.255 scope global br-lan
    inet6 fe80::20a:ebff:fe13:7b00/64 scope link 
       valid_lft forever preferred_lft forever
11: eth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether c8:3a:35:21:04:a5 brd ff:ff:ff:ff:ff:ff
12: eth3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether c8:3a:35:21:04:a1 brd ff:ff:ff:ff:ff:ff

从ttl可看出tp这个固件是基于openwrt aa (Attitude Adjustment, r10131)开发的。

然后,wan口并没有获取到IP 。。。因此wan没有正常工作。而lan口呢,电脑也不能dhcp获取ip, 设置静态ip也不能互相ping通。 再看WIFI , 也没有起来 。。。好吧,tp这是啥黑科技。

V2固件不正常,要不,再试试V1版(Archer C1200(US)_V1_160627)的固件吧,结果也是一样不工作:

Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .... 4648704 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: squash filesystem found at block 33
Creating 6 MTD partitions on "bcmsflash":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x000000ff0000 : "linux"
0x000000215000-0x000000ff0000 : "rootfs"
0x000000fb0000-0x000000fc0000 : "usb-config"
0x000000fc0000-0x000000fe0000 : "log"
0x000000ff0000-0x000001000000 : "nvram"
flash_chrdev :  flash_chrdev_init 
nflash: found no supported devices
usbmon: debugfs is not available
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Registered led device: blue:lan
Registered led device: blue:usb_1
Registered led device: blue:usb_3
Registered led device: blue:wps
Registered led device: blue:wan
Registered led device: orange:wan
Registered led device: blue:status
Registered led device: blue:wlan_2g
Registered led device: blue:wlan_5g
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1955 buckets, 7820 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
brcmnand: found no supported devices
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
devtmpfs: mounted
Freeing init memory: 204K
slhc 4123 0 - Live 0x7f000000
PPP generic driver version 2.4.2
ppp_generic 15919 0 - Live 0x7f009000
ctf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ctf 19271 0 - Live 0x7f014000 (P)
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0x400
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
bcm_robo_enable_switch: EEE is disabled
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.27 (r584393)
eth1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 9.10.178.27 (r584393)
et 70554 0 - Live 0x7f021000 (P)
et 70554 0 - Live 0x7f021000 (P)
emf 17251 0 - Live 0x7f03d000 (P)
igs 13399 0 - Live 0x7f04a000 (P)
dpsta 4559 0 - Live 0x7f056000 (P)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 36, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hotplug detected product:  1d6b/2/206
hotplug detected product:  1d6b/2/206
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 36, io mem 0x1800d000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hotplug detected product:  1d6b/1/206
hotplug detected product:  1d6b/1/206
NTFS driver 2.1.29 [Flags: R/O MODULE].
fuse init (API version 7.15)
jffs2 not ready yet; using ramdisk

Please press Enter to activate this console. button cycle succeed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP MPPE Compression module registered
ip6tnl0: Disabled Privacy Extensions
L2TP core driver, V2.0
L2TP netlink interface
gre: GRE over IPv4 demultiplexor driver
GRE over IPv4 tunneling driver
bonding: Ethernet Channel Bonding Driver: v3.7.0 (June 2, 2010)
bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
NET: Registered protocol family 24
PPPoL2TP kernel driver, V2.0
PPTP driver version 0.8.3
nf_conntrack_rtsp v0.7 loading
nf_nat_rtsp v0.7 loading
reloadconfig() begin:
no userconfig
resetconfig() begin:
resetconfig() end:
error no config
reloadconfig() end:
reload_profile() begin:
error no profile
reload_profile() end:
Load database fail.
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
device eth0 entered promiscuous mode
UTC
incorrect format cfg : cloud_config
device eth0 left promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: port 1(eth0) entering learning state
br-lan: port 1(eth0) entering forwarding state
br-lan: no IPv6 routers present
eth0.1: no IPv6 routers present
usbshare boot start
usbshare boot end
wl_module_init: passivemode set to 0x0
wl_module_init: txworkq set to 0x0
External imprecise Data abort at addr=0x2ace16f0, fsr=0x1c06, pc=0x80235780 lr=0x8023c860 ignored.
External imprecise Data abort at addr=0x2ace16f0, fsr=0x1c06, pc=0x7f447d88 lr=0x8023c860 ignored.
eth2: Broadcom BCM43c8 802.11 Wireless Controller 9.10.178.27 (r584393 WLTEST)
PCI: Enabling device 0001:01:00.0 (0140 -> 0142)
eth3: Broadcom BCM43227 802.11 Wireless Controller 9.10.178.27 (r584393 WLTEST)
kcg 333 :GPL NetUSB up!
kc   90 : run_telnetDBGDServer start 
kc  227 : init_DebugD end
INFO182B: NetUSB 1.02.80, 00020624 : Feb 24 2016 11:18:15
INFO182D: 7437: Archer C1200 :Archer C1200 
INFO182E:  AUTH ISOC
INFO182F:  filterAudio
usbcore: registered new interface driver KC NetUSB General Driver
INFO01ED:  init proc : PAGE_SIZE 4096
INFO171F:  infomap 7f997428 
INFO1722:  sleep to wait br-lan to wake up
INFO15D9: tcpConnector() started... : br-lan 
INFO1589: Bind to br-lan
HTB: quantum of class 20002 is big. Consider r2q change.
HTB: quantum of class 22100 is big. Consider r2q change.
HTB: quantum of class 22101 is big. Consider r2q change.
=====>>>>> wireless setting is finished

BusyBox v1.19.4 (2016-06-27 15:25:06 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

     MM           NM                    MMMMMMM          M       M
   $MMMMM        MMMMM                MMMMMMMMMMM      MMM     MMM
  MMMMMMMM     MM MMMMM.              MMMMM:MMMMMM:   MMMM   MMMMM
MMMM= MMMMMM  MMM   MMMM       MMMMM   MMMM  MMMMMM   MMMM  MMMMM'
MMMM=  MMMMM MMMM    MM       MMMMM    MMMM    MMMM   MMMMNMMMMM
MMMM=   MMMM  MMMMM          MMMMM     MMMM    MMMM   MMMMMMMM
MMMM=   MMMM   MMMMMM       MMMMM      MMMM    MMMM   MMMMMMMMM
MMMM=   MMMM     MMMMM,    NMMMMMMMM   MMMM    MMMM   MMMMMMMMMMM
MMMM=   MMMM      MMMMMM   MMMMMMMM    MMMM    MMMM   MMMM  MMMMMM
MMMM=   MMMM   MM    MMMM    MMMM      MMMM    MMMM   MMMM    MMMM
MMMM$ ,MMMMM  MMMMM  MMMM    MMM       MMMM   MMMMM   MMMM    MMMM
  MMMMMMM:      MMMMMMM     M         MMMMMMMMMMMM  MMMMMMM MMMMMMM
    MMMMMM       MMMMN     M           MMMMMMMMM      MMMM    MMMM
     MMMM          M                    MMMMMMM        M       M
       M
 ---------------------------------------------------------------
   For those about to rock... (Attitude Adjustment, r7549)
 ---------------------------------------------------------------
root@Akronite:/# 
root@Akronite:/# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: sit0: <NOARP> mtu 1480 qdisc noop state DOWN 
    link/sit 0.0.0.0 brd 0.0.0.0
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
    link/ether 00:0a:eb:13:7b:00 brd ff:ff:ff:ff:ff:ff
4: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 00:00:00:00:0c:14 brd ff:ff:ff:ff:ff:ff
5: eth0.1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP 
    link/ether c8:3a:35:21:04:a0 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::ca3a:35ff:fe21:4a0/64 scope link 
       valid_lft forever preferred_lft forever
6: dpsta: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN 
    link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
7: ip6tnl0: <NOARP> mtu 1460 qdisc noop state DOWN 
    link/tunnel6 :: brd ::
8: gre0: <NOARP> mtu 1476 qdisc noop state DOWN 
    link/gre 0.0.0.0 brd 0.0.0.0
9: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN 
    link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
10: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc htb state UNKNOWN 
    link/ether 00:0a:eb:13:7b:00 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.1/24 brd 192.168.1.255 scope global br-lan
    inet6 fe80::20a:ebff:fe13:7b00/64 scope link 
       valid_lft forever preferred_lft forever
11: eth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether c8:3a:35:21:04:a5 brd ff:ff:ff:ff:ff:ff
12: eth3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether c8:3a:35:21:04:a1 brd ff:ff:ff:ff:ff:ff

好吧,故事也许到这里就结束了

--EOF

Tagged in :

All Comments (0)
Gravatar image
No Comments